#electronics #smt #pick-and-place #lumenpnp #3d-printing #print-queue
# Overview
Print order for the v4.1.0 STL pack. The parts list lives in [[LumenPnP Self-Source BOM#3D print job list]], grouped by category. This note puts the same parts in the order the assembly manual uses them, timed against when the hardware arrives.
Sequence follows Opulo's [OHAI work instructions](https://ohai.opulo.io/lumen/) (X Gantry → Y Gantry → Feeder Rail → Drag Chain → Control Box → Staging Plate), then the [v4 assembly guide](https://docs.opulo.io/semi-assembly-4-0/) (Frame → Electronics), which the [DIY v4 guide](https://docs.opulo.io/guides/diy-v4/) points to as the main reference.
Rule of thumb: **run black on the main printer in queue order. Pull each accent color into one session, timed for the first phase that needs it.** Don't hold all the colors until the end.
# v4.2.0 changes
v4.2.0 was tagged 2026-10-14 (see [[LumenPnP Self-Source BOM#v4.2 — announced 2026-10, decision pending]]). Compared every v4.1.0 STL against v4.2.0 by geometry (volume, area, principal moments, oriented bounds). v4.2.0 STLs ship inside `Autobom-LumenPnP-v4.2.0.zip` → `export/`, mixed in with reference models of bought parts (nozzles, rails, steppers, cameras) — print only the ones in the queue.
| Part | v4.1.0 → v4.2.0 | Action |
|---|---|---|
| `z-gantry` (#6) | Same envelope, −5% material: cable room + mounting-hole tolerance fix from 2026-04-06 | ==**Reprint ×2 from v4.2.0**== if plate1 is already printed |
| `squaring-bracket` (#27) | Long edge 75 → 80 mm (wide-feeder clearance) | ==Reprint from v4.2.0== |
| `cable-splay` (#36) | Boolean fix, −6% material | Print from v4.2.0 |
| `peek-cable-clamp` (#35) | Redesigned, larger | Print from v4.2.0 |
| `bottom-camera-mount` (#30), `bottom-light-mount` (#32) | Redesigned for the left-side optics stack | v4.2: likely in the kit's bottom optics assembly — ==confirm before printing== |
| `board-mount-static`, `board-mount-dynamic` (#42, #43) | Redesigned for M4 thumbscrew + spring | Print from v4.2.0 |
| `board-support` (#41) | Chamfer fix, −1% | Print from v4.2.0 |
| `datum-board-mount` (#33), `static-camera-foot` (#37), `aux-staging-plate-foot` (#38), `bottom-camera-cover` (#31) | **Removed** | Skip under v4.2 |
| `bottom-vision-cover`, `bottom-vision-cable-clamp`, `cal-fid-mount` | **New** | v4.2: ==check which come assembled in the kit== |
| `discard-bin`, `discard-bin-mount` | **New** | Print (works on any v4) |
| `board-mount-flap` ×4 | **New** | Print with the board mounts |
| Everything else in P1–P4, plus `blade12/13`, `nozzle-rack`, `nozzle-camera-mask`, `top-light-mount`, `y-limit-striker`, strip feeders | Identical (≤0.1 mm deviation) | No change |
# Hardware gates
| Arrives | What lands | What it unlocks |
|---|---|---|
| On hand | Z-Axis Linear Rail Set | `x-gantry-front` rails |
| On hand | Control Box — assembled, in its printed enclosure + lid | Electronics; nothing to print |
| ~2026-10-13 | Frame Kit, Fastener Kit, NEMA 17 ×4, GT2 Kit | Z-belt subassembly, X motor/idler mounts, Y leg subassemblies |
| ~2026-10-19 | MGN12H Rail Kit, Feeder Connection Kit | X linear axis, Y rails, feeder rails, most of the frame |
| Steps 5–7 + 2 wk | Toolhead kits, cameras, ring lights, endstops, drag chain, datum board, staging plates | Toolheads, top camera/light, staging plate, drag chain, electronics |
Dates are Opulo's published lead times from the BOM note, not observed delivery dates.
# Print queue
Solid volume measured from the STLs. Phase share = that phase's fraction of all the plastic, control box excluded.
## P0 — Calibration and jigs (now)
| # | Part | Qty | Material | Why | Printed? |
| --- | ------------------------------------ | --- | -------------- | -------------------------------------------------------- | ---------- |
| 1 | `FDM-8000_corndog` | 1 | Jet Black PETG | Fit check — 20×20 socket, M3/M5 features | yes |
| 2 | `FDM-8000_corndog` | 1 | Yellow PLA | Gates the yellow session | yes |
| 3 | `z-belt-alignment-jig` | 1 | Black PLA | Positions the backplates on the 130T loop — first X step | plate-jigs |
| 4 | `linear-rail-2020-alignment-fixture` | 2 | Black PLA | Centers MGN12H on 2020 — X and Y rails | plate-jigs |
| 5 | `top-camera-focus-jig-v4` | 1 | Black PLA | Optional; needs Datum Board + 4× M3×10 + nuts | plate-jigs |
Jigs 3–5 are **not in the STL pack**. They're on the [OHAI Jigs page](https://ohai.opulo.io/lumen/jigs/) (CERN-OHL-W). OHAI specifies PLA for jigs, and they don't need ASA.
## P1 — X gantry (OHAI §1) · ~21% of plastic
| # | Part | Qty | Color | Used at | Printed? |
| --- | -------------------------- | --- | --------- | -------------------------------------------------- | -------------------------- |
| 6 | `z-gantry` | 2 | Black | Z carriages; NEMA 11 + toolhead mount here | plate1 |
| 7 | `x-gantry-front` | 1 | Black | Z rails, Z motor, idler, z-gantries | plate1 |
| 8 | `z-gantry-backplate-left` | 1 | **Red** | z-belt subassembly | yes (came with motion kit) |
| 9 | `z-gantry-backplate-right` | 1 | **Blue** | z-belt subassembly — drill striker hole 2.5 mm | yes (came with motion kit) |
| 10 | `x-motor-mount` | 1 | Black | X NEMA 17, XY limit board | plate2 |
| 11 | `x-idler-mount` | 1 | Black | Carries the X tension arm | plate2 |
| 12 | `belt-tension-arm` | 1 | Yellow* | On `x-idler-mount` | |
| 13 | `x-gantry-back` | 1 | Black | Rides the 525 mm rail; top camera + light | plate1 |
| 14 | `belt-clamp` | 2 | Yellow* | X belt to `x-gantry-back` | |
| 15 | `nozzle-camera-mask` | 2 | Black | Slides onto each nozzle holder at toolhead install | plate1 |
| 16 | `top-light-mount` | 1 | **White** | Holds the top ring light on `x-gantry-back` | |
`z-gantry` goes first because the Step 5 toolhead kits are built around it. The red and blue backplates go in the **z-belt subassembly**, the first X gantry work you can do once the GT2 kit arrives. They can't wait until the end.
## P2 — Y gantries (OHAI §2) · ~40% of plastic
| # | Part | Qty | Color | Used at | Printed |
| --- | ---------------------- | --- | ----------- | ----------------------------------------- | ------- |
| 17 | `front-left-leg` | 1 | Black | Gets a tension arm + Y-striker square nut | plate4 |
| 18 | `front-right-leg` | 1 | Black | Mirror of left | plate4 |
| 19 | `back-leg` | 2 | Black | Y motors mount here | plate3 |
| 20 | `y-gantry-left` | 1 | Black | Rides the 550 mm rail | plate3 |
| 21 | `y-gantry-right` | 1 | Black | Mirror | plate3 |
| 22 | `belt-tension-arm` | 2 | Yellow* | One per front leg | |
| 23 | `belt-clamp` | 4 | Yellow* | Two per Y gantry | |
| 24 | `extrusion-cable-clip` | 16 | Black - PLA | 3 per Y gantry now; rest at Electronics | |
The legs plus leg extensions are **~43% of the build's plastic**. They're the longest and most warp-prone prints, so use the enclosed printer. If you have a second printer, start the legs there in parallel with P1.
## P3 — Feeder rails (OHAI §3) · ~12% of plastic
| # | Part | Qty | Color | Used at | Need by |
|---|---|---|---|---|---|
| 25 | `blade12` | 2 | Yellow | Holds 12-slot blade PCB | ~10-19 |
| 26 | `blade13` | 2 | Yellow | Holds 13-slot blade PCB | ~10-19 |
OHAI's QC checks every blade **flat on a granite block** before the PCB goes in. At 190–205 mm long and thin, these carry the ASA warp risk. Check them on a surface plate.
## P4 — Frame (v4 guide → Frame) · ~13% of plastic
| # | Part | Qty | Color | Used at | Need by |
| --- | --------------------- | --- | ----------- | ---------------------------------------------------------------------------------------------- | ---------- |
| 27 | `squaring-bracket` | 1 | Black - PLA | Back-rail spacing (50 mm side), staging-plate alignment, holds nuts for the Y drag-chain bolts | plate-jigs |
| 28 | `front-leg-extension` | 2 | Black | After X is mounted on Y | plate5 |
| 29 | `back-leg-extension` | 2 | Black | Same | plate5 |
| | | | | | |
## P5 — Staging plate, drag chain, plates (OHAI §4, §6; Frame → Plates) · ~9% of plastic
| # | Part | Qty | Color | Used at | Printed? |
| --- | --------------------------- | --- | --------------- | --------------------------------------------------------- | -------- |
| 30 | `bottom-camera-mount` | 1 | Yellow | Bottom camera assembly | |
| 31 | `bottom-camera-cover` | 1 | Yellow (medium) | Same | |
| 32 | `bottom-light-mount` | 1 | **White** | Bottom ring light diffuser | |
| 33 | `datum-board-mount` | 1 | Black | Datum board to staging plate | |
| 34 | ~~`secondary-fid-bracket`~~ | — | — | Comes in the Secondary Fiducial Upgrade Kit — don't print | — |
| 35 | `peek-cable-clamp` | 3 | Black | Staging-plate cable management | |
| 36 | `cable-splay` | 1 | Black | Head end of the drag chain, bolts to `x-gantry-back` | |
| 37 | `static-camera-foot` | 1 | Black | Under the bottom camera at plate mounting | |
| 38 | `aux-staging-plate-foot` | 1 | Black | Second plate foot, M3×14 + square nut | |
| 39 | `y-limit-striker` | 1 | Black | Set against the Y endstop (Endstop Set) | |
## P6 — Commissioning and work holding · ~5% of plastic
| # | Part | Qty | Color | Notes |
|---|---|---|---|---|
| 40 | `nozzle-rack` | 1 | **White** | Light color helps the tool changer; needs the nozzle set |
| 41 | `board-support` | 8 | White | Getting Started Kit hardware |
| 42 | `board-mount-static` | 4 | White | Same |
| 43 | `board-mount-dynamic` | 4 | **White PETG** | Needs the flex — not ASA |
| 44 | `8mm-strip-feeder` | as needed | Black | Each takes 2× M3×10 ULP + 2× wing nuts |
# Color sessions
| Session | Parts | When |
|---|---|---|
| **Red + Blue** | #8, #9 | During P1, before ~10-13. Two tiny parts; can share a plate on an MMU3 if one is set up for ASA |
| **Yellow** (Ambrosia) | #12, #14, #22, #23, #25, #26, #30, #31 — all tension arms, belt clamps, blades, bottom camera mount + cover | Once, right after corndog #2 passes. Tension arms needed ~10-13, blades by ~10-19. ~15% of the plastic |
| **White ASA** | #16, #32, #40, #41, #42 | Once, before the Steps 5–7 hardware arrives |
| **White PETG** | #43 | Last |
| **Black** | Everything else | Main printer, queue order |
# Conditional and skip
- `control-box` + `control-box-lid` — **skip.** Confirmed 2026-10-09: the Control Box arrived assembled in its printed enclosure with the lid. These two are ~14% of the pack's plastic (330 of 2,415 cm³ solid), so the 1.3–1.5 kg filament budget in [[LumenPnP Self-Source BOM]] comes down by about that much.
- `secondary-fid-bracket` — **skip.** Buying the Secondary Fiducial Upgrade Kit, which includes the bracket.
- `blade-adapter-pin-cover` — **skip.** Part of the Feeder Cable Adapter for v2.x–v3.2 machines. v4 connects directly.
- `12/16/24/32mm-strip-feeder`, `adj-strip-feeder` — optional, print when a tape width needs one.
# Decisions
Where this departs from the plan in [[LumenPnP Self-Source BOM]]:
- **Colors print by phase, not at the end.** The BOM note's TODO saved the white diffusers, red/blue backplates and yellow accents for last. OHAI puts the red/blue backplates in the z-belt subassembly (first X step), the yellow tension arms in the X idler and front-leg subassemblies, and the nozzle masks on at toolhead install.
- **Frame parts (P4) jump ahead of drag chain, control box and staging plate.** That's off OHAI's order, but those three all wait on the Steps 5–7 order. Most of the Frame page can go together once the rails arrive (~10-19). Its squareness check needs a staging plate.
- **`squaring-bracket` is a final-assembly tool, not a Step 4 one.** OHAI uses it to space the back feeder rail, align the staging plates and hold nuts for the Y drag chain.
- **`secondary-fid-bracket` is in the v4.1.0 pack** but missing from the BOM note's print list. The OHAI staging-plate step installs it. Moot for printing now that the kit is being bought (below).
- **Secondary fiducial resolved: it's not on the datum board.** It's the printed `secondary-fid-bracket`, bolted to the primary staging plate with 2× M3×10 hex head and 2× M3 nuts. The $7.50 [upgrade kit](https://ohai.opulo.io/diy-components/secondary-fiducial-upgrade-kit/) is that bracket plus hardware and a bag of cardstock punch-outs. The screws are the same generic M3×10 hex-head + nut the board mounts use (Board Mounting Hardware, Step 7). The Datum Board order isn't blocked either way.
- **Buying the Secondary Fiducial Upgrade Kit anyway (decided 2026-10-09).** It brings the bracket and hardware, so `secondary-fid-bracket` comes off the queue.
# TODO
- ==Settle `belt-tension-arm` vs `belt-clamp` yellow before the yellow session== (Discord `#lumenpnp-builds`). Don't let it hold up ~10-13. They're 2–10 cm³ each and cheap to reprint.
- ~~Check the Control Box for its enclosure on arrival before queueing `control-box` + lid.~~ (done 2026-10-09 — arrived assembled with enclosure and lid)
- ==OHAI's `x-gantry-spacer-jig` and x/y/z pulley-spacer jigs are unpublished== ("to be added" on the Jigs page). Set `x-idler-mount` depth and pulley heights by measurement.
- ==Bottom camera focus jig is STEP-only== on the Jigs page. Export to STL if I want it.
- ~~Carry back into [[LumenPnP Self-Source BOM]]: Control Box arrived assembled with its printed enclosure; buying the Secondary Fiducial Upgrade Kit ($7.50); `control-box`/lid and `secondary-fid-bracket` off the print list.~~ (done 2026-10-09)
- ==Reprint `z-gantry` ×2 and `squaring-bracket` from the v4.2.0 export== (see [[#v4.2.0 changes]]).
- ==Hold P5 and the board mounts in P6 until the v4.2 decision is made.== P1–P4 are unaffected apart from the two reprints.
# References
- [[LumenPnP Self-Source BOM]] — parts list, color callouts, hardware order log
- STL pack: `Dropbox/Making/Electronics/LumenPNP/v4.1.0 Release/LumenPnP-STLs-v4.1.0` (46 files incl. corndog)
- OHAI: [X Gantry](https://ohai.opulo.io/lumen/x-gantry/) · [Y Gantry](https://ohai.opulo.io/lumen/y-gantry/) · [Feeder Rail](https://ohai.opulo.io/lumen/feeder-rail/) · [Drag Chain](https://ohai.opulo.io/lumen/drag-chain/) · [Control Box](https://ohai.opulo.io/lumen/control-box/) · [Staging Plate](https://ohai.opulo.io/lumen/staging-plate/) · [Additional Parts](https://ohai.opulo.io/lumen/additional-parts/) · [Jigs](https://ohai.opulo.io/lumen/jigs/)
- v4 assembly: [Frame](https://docs.opulo.io/semi-assembly-4-0/frame/) · [Electronics](https://docs.opulo.io/semi-assembly-4-0/electronics/)
- OHAI source: [opulo-inc/ohai](https://github.com/opulo-inc/ohai) (`docs/lumen/`)
# Changelog
## 2026-10-09
- Note created. Ordered the v4.1.0 STL pack against the OHAI work instructions (opulo-inc/ohai `main`, pulled 2026-10-09) and the v4 assembly Frame/Electronics pages, timed to the hardware gates in [[LumenPnP Self-Source BOM]].
- Measured all 46 STLs (bounding box and solid volume) for the phase shares.
- Control Box confirmed arrived with its printed enclosure + lid → `control-box`/`control-box-lid` moved to skip. Secondary Fiducial Upgrade Kit being bought → `secondary-fid-bracket` (#34) struck from the queue. Updated hardware gates, Decisions and TODO to match.
- Carried the Control Box, secondary fiducial and print-list changes back into [[LumenPnP Self-Source BOM]].
## 2026-10-20
- Added [[#v4.2.0 changes]]: geometry diff of every v4.1.0 STL against the v4.2.0 export, with reprint / skip / new calls. Added TODOs to reprint `z-gantry` and `squaring-bracket` and hold P5 + board mounts for the v4.2 decision.