# Making Solder Paste Stencils with a Fiber Laser Research date: 2026-10-21 Equipment available: 100 W MOPA fiber laser with a 300 × 300 mm field lens. A smaller field lens is an option. ## Assessment Making stencils looks practical with this equipment, but keeping the foil flat and getting clean, accurately sized apertures are the difficult parts. Cutting through the material alone does not establish that the stencil will print well. Several useful demonstrations and workflows are available, although most detailed DIY examples use aluminum. This research did **not** find a complete, verified **100 W MOPA + stainless** recipe specifying lens, frequency, pulse width, speed, and passes. Published settings below belong to the demonstrated machines and materials; they are not validated settings for the available 100 W laser. ## Videos and Accompanying Workflows ### 1. Saheen Palayi — Turn a Soda Can Into a PCB Solder Paste Stencil - [YouTube video](https://www.youtube.com/watch?v=kIlWCu9ktq0) - [Detailed Hackster article](https://www.hackster.io/saheenpalayi/how-i-made-my-own-pcb-solder-paste-stencils-at-our-fab-lab-6b5bb8) **Best complete walkthrough.** Documents preparing soda-can aluminum, converting Gerbers, cutting with an xTool F1 Ultra, aligning the stencil, and applying paste. The author's workflow converts Gerbers to PNG and then extracts cutting outlines in xTool software. Direct vector export from the PCB design software is preferable when available, to avoid that intermediate raster conversion. Published settings: | Parameter | Reported value | |---|---| | Laser | xTool F1 Ultra, fiber IR | | Material | Soda-can aluminum | | Power | 100% | | Speed | 600 mm/s | | Passes | 10 | | Cutting time | Under 20 seconds, as reported by the author | The article also shows failures: heat distortion, apertures needing manual clearing, and damaged borders around tiny sensor pads. Those limitations make it particularly useful. ### 2. Mikey Sklar — Full Metal Stencil - [YouTube video](https://www.youtube.com/watch?v=vPO3uMIyp_U) - [Project repository, materials, and settings](https://github.com/mikeysklar/full-metal-stencil) Uses **0.18 mm aluminum business-card blanks and a 20 W fiber laser**, followed by inspection and stencil printing. The repository includes material links, laser settings, example boards, and a stencil-jig reference. The published settings table says **power 80 / speed 600 / passes 220**, but omits units. Do not silently interpret the speed value as a verified unit-bearing setting. This is a useful demonstration of a repeatable small-board workflow. **180 µm should not be adopted as a general-purpose thickness for fine-pitch boards.** ### 3. Electronoobs — Laser Cut Stencil & PCB, ComMarker B6 - [YouTube video, starting at the stencil segment](https://www.youtube.com/watch?v=b9Dywpz8J8s&t=452s) The closest video in this shortlist to a conventional standalone galvo-fiber setup. - **7:32:** PCB & Stencil - **9:07:** Apply Solder Paste Useful visual demonstration, although the accessible chapter information does not establish the stencil alloy, thickness, or a complete cutting recipe. It should not be treated as a verified stainless settings reference. ### 4. Eurocircuits — Making Solder Paste Stencils - [Vimeo video](https://vimeo.com/421695780) - [Accompanying article and complete transcript](https://www.eurocircuits.com/technical-guidelines/assembly-manufacturing-technology/making-solder-paste-stencils/) **Best stainless-process reference.** Describes: - **70, 100, and 130 µm stainless** stock. - Stretching the foil in a frame. - Choosing cutting parameters by aperture size. - Cutting with a dedicated LPKF StencilLaser P6060. - Polishing away exit-side burrs. Its value is showing the workholding and finishing process rather than supplying transferable settings for a MOPA galvo laser. ## Written Process Notes: Heat, Workholding, and Focus ### AyLo — PCB Stencils (or Tiny Metal Parts) on the Xtool [Read the article](https://aylo6061.com/2025/07/14/pcb-stencils-or-tiny-metal-parts-on-the-xtool/) The most useful practical process notes found. Three lessons transfer well to other galvo setups: 1. **Spread out the cutting order.** Repeatedly cutting neighboring apertures concentrates heat and deforms the webs between them. 2. **Use many light passes.** The aluminum example uses **100% power, 8,000 mm/s, and hundreds of passes**. For small apertures, the author reports batches of **50 passes, a 10-second pause, and repetition up to 500 total passes**. 3. **Control workholding and focus.** The article documents a removable tape fixture and manually refining focus. The fixture uses an aluminum block, removable double-sided tape, painter's tape, and then the stock; the release layer helps avoid bending during removal. These are aluminum/xTool settings, not stainless settings. The reported stencil was usable, but the author wanted thinner stock to reduce paste deposition. ### StenciLaser — Cut Ordering to Reduce Local Heating [Project repository and instructions](https://github.com/Aylo6061/StenciLaser) The author's follow-up tool takes a DXF and reorders apertures to separate consecutive cuts spatially. It exports xTool `.xs`/`.xcs` files. In xTool Studio, **cut order must be set to “by layer”** for the ordering to take effect. The software targets xTool, but the heat-management idea is relevant to any galvo workflow. It is not a guarantee against warping, particularly for dense adjacent geometry. ## Stainless Stock Sources Prices below are indicative listings found during research, before shipping. Confirm current prices and availability when ordering. | Source | Specific stock | Purchasing notes | |---|---|---| | [Trinity FSQ-4](https://www.trinitybrand.com/item/302-304-full-hard/stainless-steel-shim-flat-sheets/fsq-4) | **12 × 12″ flat sheet, 0.004″ / 101.6 µm, full-hard 302/304** | About **$12 per sheet** in retrieved listings. Recommended first inexpensive experimental purchase. | | [Trinity 630112-4](https://www.trinitybrand.com/item/stainless-steel/stainless-steel-1/630112-4) | **6 × 12″ flat sheet, 0.004″, full-hard 301** | Listed at **$6.26**. Smaller, inexpensive test stock. | | [McMaster stainless shim sheets](https://www.mcmaster.com/products/stainless-steel-shim-stock-sheets/) | **6 × 25″ full-hard 18-8 sheets** | **9011K62 = .003″; 9011K42 = .004″; 9011K43 = .005″.** Convenient industrial sourcing; prices were not visible. The listing says 18-8, not specifically certified 304. | | [Datum Alloys SMT stencil foils](https://datumalloys.com/smt-surface-mount-technology/smt-stencil-foils/) | **PhD 304 and Fine Grain 304**, specifically engineered for stencils | Best lead for proper stencil material. US operation in Binghamton, NY. Small-order minimums and pricing require inquiry. | | [Penta Material](https://www.pentamaterial.com/) | **304 HTA tension-annealed stencil foil** | Another specialist foil source. | ### Thickness Conversion | Inch thickness | Metric thickness | |---|---| | 0.003″ | 76.2 µm | | 0.004″ | 101.6 µm | | 0.005″ | 127.0 µm | ### Shim Stock Versus Stencil-Grade Foil **Ordinary full-hard shim stock and stencil-grade foil are not interchangeable specifications.** Datum's foil is stress-relieved to reduce cutting distortion; its fine-grain material also targets smoother aperture walls. See [Datum's material and stencil-design discussion](https://datumalloys.com/optimizing-smt-stencil-design-based-on-pcb-layout/). For initial experiments, inexpensive flat shim sheets are a reasonable test material. If distortion limits the results, compare against actual stencil foil before attributing all failures to laser parameters. Suggested specialty-material inquiry: > 100 µm, flat, unmounted, stress-relieved SMT stencil foil, with 75 µm samples if available. ## Lens Choice for the Available 100 W MOPA The existing lens has a **300 × 300 mm field**. Test it before purchasing another lens. A shorter-focal-length lens generally gives a smaller focused spot with the same incoming beam, which helps preserve narrow webs and small apertures. Exact spot size also depends on beam diameter and quality, so field size alone cannot establish the minimum achievable feature size. See [Thorlabs' scan-lens explanation](https://punchout.thorlabs.com/newgrouppage9.cfm?objectgroup_id=6430). Provisional recommendation: - **110 × 110 mm field** if the complete aperture pattern fits. - Around **150 × 150 mm field** if more coverage is needed. - The surrounding uncut stencil margin can extend beyond the marking field. These are candidate field sizes, not verified compatible lens part numbers. Confirm compatibility with the laser supplier and recalibrate after changing lenses. [LightBurn lens configuration guidance](https://docs.lightburnsoftware.com/latest/Reference/DeviceSettings/GalvoBasicSettings/) ## Recommended First Stainless Trial This is a proposed trial workflow synthesized from the sources, not a tested recipe for the available machine. 1. **Export the paste layer directly as vector artwork where possible.** For KiCad, use `F.Paste` or `B.Paste` and SVG/DXF export. Verify dimensions and orientation after import. [KiCad plotting documentation](https://docs.kicad.org/9.0/en/pcbnew/pcbnew.html) 2. **Cut a small test pattern in roughly 100 µm stock.** Include the actual smallest pads and narrowest webs required by the target board. 3. **Tune focus and cutting parameters on that pattern.** Spread cuts spatially and inspect between batches of passes. Do not directly copy aluminum settings to stainless. 4. **Measure aperture size and compensate for kerf.** Remove cutout remnants and burrs without bending the foil. [LightBurn kerf guidance](https://docs.lightburnsoftware.com/latest/Guides/Test-KerfOffset/) 5. **Make a test paste print before cutting the full stencil.** Thickness and aperture geometry affect release as well as paste volume. Indium recommends an aperture area ratio of at least approximately **0.66** as a general starting guideline. [Indium stencil-design guide](https://documents.indium.com/qdynamo/download.php?docid=645) ## Remaining Unknowns - Exact laser source and scan-head model. - Current control software. - Actual focused spot size and calibration across the existing lens field. - Smallest aperture and narrowest web required by the intended boards. - A verified stainless recipe for this machine, including frequency and pulse width. - Small-quantity availability and price of specialty stencil foil.