#reflow #electronics #pcb #oven #reflow-master-pro #ninja # Overview Converting a Ninja **FT205CO** into a solder-reflow oven driven by an Unexpected Maker [[Reflow Master Pro]] (RMP) and a solid-state relay, following the Ace's Electronics SP101 build ([[Ninja SP101 reflow oven mod using Reflow Master Pro and an SSR – Ace's Electronics]]). The FT205CO is the Costco SKU of the **SP201 Digital Air Fry Pro** — same flip-up family as the SP101 Ace used, with the "extended height" cavity. 120 V / 60 Hz / 1800 W per the owner's guide. Side panel is off and the stock SharkNinja board is exposed as of 2026-11-09. The plan is the same as Ace's: pull the SharkNinja controller, put every heating element behind one SSR, hardwire the convection fan (and light), and let the RMP run the show from two thermocouples. # Resources - [[Reflow Master Pro]] — terminal map, schematic, captured docs, saved files - [[Ninja SP101 reflow oven mod using Reflow Master Pro and an SSR – Ace's Electronics]] — the reference build (Clippings); its wiring diagram is embedded under Design below - [Ninja FT205CO Owner's Guide (Costco PDF)](https://mobilecontent.costco.com/live/resource/img/static-us-pdf/9413025_UserManualandWarranty.pdf) — 120 V~ 60 Hz, 1800 W; max 500 °F (Broil HI / Pizza); the bay cooling fan runs until the unit is below 95 °F - [Ninja support copy of the same guide](https://support.ninjakitchen.com/hc/en-us/article_attachments/11732474560412) - [SP100/SP101 series FAQ](https://old-support.ninjakitchen.com/hc/en-us/articles/4403151980306-SP100-Series-Ninja-Foodi-Digital-Air-Fry-Oven-FAQs) — SP101 is 19.72 × 14.96 × 7.56 in; "different elements run at different power levels depending on the function" - [SP201 vs FT205CO](https://kitchprep.com/ninja-sp201-vs-ft205co/) — identical hardware, FT205CO adds Pizza/Reheat presets and a broil rack; 15.3" D × 20.2" W × 8.1" H closed - [iFixit — SP101 heating coil replacement](https://www.ifixit.com/Guide/Ninja+Foodi+SP101+Heating+Coils+Replacement/170991) and [control panel replacement](https://www.ifixit.com/Guide/Ninja+Foodi+SP101+Control+Panel+Replacement/171116) — disassembly order (TR10 on the lever bar, PH1/PH2 everywhere else) - [EEVblog — Ninja SMT Reflow Oven](https://www.eevblog.com/forum/projects/ninja-smt-reflow-oven/) — AU 2400 W SP101 conversion: 3 × 650 W top + 3 × 333 W bottom tubes; author ran 2 top + 1 bottom (1633 W); stock NTC in the top-left rear corner was too slow and read cage heat; cavity measured ~14 L - [Printables — Reflow Master Pro housing for Ninja toaster](https://www.printables.com/model/640370-reflow-master-pro-housing-for-ninja-toaster) (whoppingpochard) — page sits behind a Cloudflare check for me; ==confirm which Ninja it fits before printing==. From their build photo: white hockey-puck SSR on a generic black-anodized SSR extrusion (~puck footprint, ~40 mm fins) in the tray with the bay fan below it; Wago 221 lever nuts in printed holders for all the junctions; a small internal AC-DC module board feeding the RMP; convection fan hardwired on silicone leads. Their own caption flags the factory yellow (cord-side neutral) wrongly landed on the Wago bus in the photo — i.e. they also kept the TCO in the neutral leg. # What's inside (2026-11-09 photo) ![[media/ninja-ft205co-side-panel-off.jpg]] - **Mains entry**: cord enters the rear through a strain relief; green ground lead lands on a chassis stud (keep it) - **SharkNinja board** `SN P/N SP3XXUS-…` rev 2021, in the vertical bay on the control side: - on-board switch-mode supply (yellow-taped transformer), `F1` = T2A 300 V fuse on that supply, `ACL` silk at the mains input - big finned aluminium heatsink = TRIAC that modulates the elements - Yuanze `Y3F-SS-112DMF` relay, 12 V coil, 15 A @ 125 VAC — the element master relay - buzzer, 4-pin programming header, red 2-pin connector - this whole board goes; the SSR + RMP replace the TRIAC + relay + logic - **Element terminals**: two visible at the top of this wall, ceramic insulators, fibreglass-sleeved leads, marked **120 V 583 W**. A black lead daisy-chains the two terminals, so that is a shared leg of two separate elements. - **Convection fan**: shaded-pole AC motor bolted to the cavity wall, shaft through to the fan inside. ==Read the motor label — expect 120 V~== - **Bay cooling fan**: small cream brushless DC fan with a 3-conductor sleeved lead (black/yellow/blue — power + tach). ==Read the label; expect 12 V. Measure the frame size.== - **Wire colours inside** are SharkNinja's own (black, red, blue, white, yellow) — not line/neutral by colour. Map them with a meter before cutting anything. - **Thermal cutoff (TCO)**: in the **neutral** leg. Cord neutral → yellow lead → one-shot axial thermal fuse in white fibreglass sleeving, pressed flat to the cavity wall by a stamped sheet-metal clamp (lower left of the photo) → white lead → loads. Leads are factory crimp-spliced (the crimp is the shiny lump where the white wire ends). Stays exactly where it is — see Design. ==Slide the sleeve back and read the rating on the body== - Wire-colour map so far: **yellow** = cord-side neutral (before TCO), **white** = load-side neutral (after TCO) - ==Interior lamp — locate it and its two leads== - ==Stock NTC thermistor — probably top-left rear like the SP101; comes out with the board== ## Element math - 583 W @ 120 V → 24.7 Ω, 4.86 A per element (sanity check with a meter: ~25 Ω cold) - 3 × 583 W = 1749 W ≈ the 1800 W nameplate once the fan motor is added, so expect **three** 583 W elements, most likely the top bank; the FAQ and owner's guide both talk about separate upper and bottom elements that the stock controller runs in different combinations - A 15 A cord/plug and a 15 A branch circuit cap the SSR load at **~1750 W** (14.6 A). Whatever elements exist, the set wired to the SSR has to sum to ≤ that. If there are bottom elements too, a top + bottom mix (like the EEVblog 2-top + 1-bottom build) heats a PCB more evenly than top-only. - Volume check against the RMP guidance (≤ 18 L, ≥ 1300 W): the SP101 cavity measured ~14 L; the SP201 is taller. ==Measure the cavity (W × D × H) — at ~1750 W the oven stays above the 100 W/L rule of thumb up to 17.5 L== # Design Ace's SP101 diagram, for reference (fan and light always on, heater bars through the SSR): ![[Pasted image 20260211124505.png]] ## Wiring diagram ![[media/ninja-ft205co-reflow-wiring.svg]] Colours in the diagram are by function (line / switched line / SSR output / neutral / ground / +5 V / switched-low / thermocouple / E-Kill), not the factory wire colours. The two factory colours that matter are called out: the **yellow** lead is the cord-side neutral into the TCO, the **white** lead is the load-side neutral out of it. `⟨L′⟩` and `⟨N′⟩` are the taps for an internal 5 V module if you go that way instead of a USB-C adapter. A 2× PNG of the same drawing is at `media/ninja-ft205co-reflow-wiring.png`; the SVG was generated from a script, so it is easy to regenerate once the element count is known. ## Mains connections | From | To | Notes | |---|---|---| | Cord L (black) | Master switch | Illuminated DPST rocker rated ≥ 15 A/125 VAC; switch L (and N if DPST) | | Master switch | SSR `A1` | Line feed to the SSR | | SSR `A2` | Element hot ends | All chosen elements in parallel. Reuse the factory daisy-chain leads/terminals where they fit | | Element other ends | White neutral (load side of the TCO) | No switching on the neutral side. Every return — elements, fan, lamp, 5 V module — goes through the factory TCO, so it protects the SSR path however the SSR fails | | TCO | Leave as found | Factory crimps, factory clamp, neutral leg. Don't unclip, move or solder it — heat from reworking a one-shot TCO can trip it. If it ever opens, replace like-for-like (same form factor, same or one step higher rating); never bypass. After a trip the elements sit at line potential — unplug before probing | | Master switch | Aux fuse → aux branch | **Littelfuse 0215002.MXP** (T 2 A, 250 V, 5×20 ceramic, 1500 A I.R.) in a **McMaster 7087K43** panel-mount holder (5×20, 250 VAC, 0.25" straight QD tabs; 7087K44 = 90° elbow tabs) next to the master rocker, so it can be changed from outside. Everything that isn't an element hangs off this fused branch. Step to T 2.5 A only if the fan measures > ~0.8 A running | | Aux fuse | Convection fan motor | Hardwired on (Ace's approach, proven). Inductive load — if you later move it to AUX2 + SSR, on/off only. ==Check the motor label for "impedance protected" / thermal protector== | | Aux fuse | Interior lamp | Optional; hardwire on with the fan or leave disconnected | | Aux fuse | 5 V module AC in (`⟨L′⟩`) | Only if powering the RMP internally | | Cord G (green) | Chassis stud | Existing; also bond the SSR heatsink/mounting plate if it is not already on the chassis | Wiring practice: - Element path carries 15 A continuous: 14 AWG (16 AWG minimum) high-temperature wire — silicone or fibreglass/mica sleeved like the factory leads. Reuse the factory sleeved leads and ceramic-insulated terminals wherever possible. - Crimped ring or high-temp quick-disconnects on the element studs; no solder in the hot zone. - Keep the SSR and all new mains wiring in the electronics bay (where the SharkNinja board was), away from the cavity wall. - Nothing stays live when the master switch is off — the 5 V module, fan and lamp all hang off the switched side. - The aux fuse protects the 18-ish AWG fan/lamp leads, which otherwise sit behind nothing but the 15 A branch breaker. It will not catch a stalled shaded-pole motor (locked-rotor current is only ~1.5–2× running) — that is what the motor's own impedance/thermal protection is for. No fuse on the element path: a 15 A fuse duplicates the breaker and one that carries 14.6 A continuously would have to be a 20 A anyway; the TCO and the RMP max-temp cutoff cover that leg. ## Low-voltage connections (RMP) Full terminal map with schematic nets is in [[Reflow Master Pro]]. Short version: | RMP terminal | Wire to | Notes | |---|---|---| | SSR + / − | SSR DC input + / − | RMP sources 5 V on + and sinks − through an NPN; polarity matters | | AUX1 + / − | Bay cooling fan | Option 1: swap the 12 V fan for a 5 V fan of the same frame size and wire it straight here. Option 2: keep the 12 V fan — AUX1 → RM Fan Controller signal in, fan on the controller's load side from a 12 V module | | AUX2 + / − | spare | Later: a second small SSR for the convection fan so profiles can switch it. On/off only | | TC1 red / white | Top probe | Match red/white to the probe leads | | TC2 red / white | Bottom probe | | | E-KILL | NO momentary pushbutton | Pressing it shuts the RMP's 5 V rail down (hardware, not firmware) and the SSR drops | | DC jack or USB-C | 5 V supply | USB-C adapter via a panel-mount pass-through is simplest; an internal Mean Well IRM-10-5 into the barrel jack keeps it one cord. ==Check barrel size/polarity on the RMP before buying a plug== | ## Thermocouples - RMP guidance: top probe 1–2 cm above the PCB, bottom probe within 1 cm of the oven floor; with one probe only, it must be the top one; with two, the controller uses the average. - Ace put both at rack height, one forward and one rear — also works. - Bring them through the cavity wall via a small drilled hole with a high-temp grommet, or an existing vent slot; strain-relieve outside. - Keep the tips off the metalwork — the MAX31855 inputs float, and a grounded tip gives read errors. - The supplied probes are fine to start; for repeated >190 °C work, glass-braid or stainless-sheathed *ungrounded* K-types (e.g. [Adafruit 270](https://www.adafruit.com/product/270)) last longer. ## SSR and heatsink - Load is 15 A at 120 V. Use a **25 A minimum, 40 A preferred** panel-mount ("hockey puck") SSR, zero-crossing, 3–32 VDC input, 24–280 VAC output. - Expect ~1–1.6 V on-state drop × 15 A ≈ 15–24 W of heat. A heatsink is not optional; mount it in the bay in the cooling fan's airflow, with the thermal pad. - Candidates: - Sensata/Crydom **D2425** or **D2440** — DigiKey ([D2425](https://www.digikey.com/en/products/detail/sensata-crydom/D2425/139477)) - AutomationDirect **AD-SSR6 series** (`AD-SSR625-DC-280A` 25 A SCR, `AD-SSR640-DC-280A` 40 A SCR, `AD-SSR6T40-DC-280A` 40 A TRIAC; 3–32 VDC in, 24–280 VAC out, zero-cross, thermal pad included) — [spec sheet](https://cdn.automationdirect.com/static/specs/oldspec/ssclass6relays_2026_07_22.pdf). ==The 25 A SCR page shows as a retired product — confirm what's current before ordering, and pick the matching AD heatsink== ## Parts list (so far) | Item | Part | Source | Notes | | ------------------------------------------------ | ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ | ------------------------------------------------------------- | ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- | | SSR | **Teledyne Relays SHC23D25** (on hand) — 25 A, 24–265 VAC, 3–32 VDC, zero-cross, IP20 cover, 58.2 × 44.8 × 28.8 mm hockey puck, max operating 70 °C | Mouser | Spelled SHC, not SCH. Teledyne's datasheet links redirect to their new site — thermal curves not retrieved; sizing below uses typical SCR-puck figures (~1.1–1.6 V drop → 16–23 W at 14.6 A) | | SSR heatsink | **Sensata/Crydom HS251** (DigiKey CC1695-ND, $25.54; HS172 = CC1698-ND, $32.29) — 58.7 × 50.3 × 38.4 mm, 99 g, 2.5 °C/W natural, panel mount, hardware kit included (8-32 / M4, 20 in-lb). Crydom rates a 25 A puck on it at 28 A @ 40 °C in still air. Alt if ~100 mm fits: **HS172** (same profile, 100.3 mm long, 1.7 °C/W) | DigiKey | 58.7 mm wide = the NF-A6x15 covers the end face; blow along the fins, fins vertical. Expect ~1.2–1.5 °C/W with the fan → base ≈ 25–30 °C over bay ambient at 20 W. Stand it off the plastic tray or bolt it to the steel panel (also the chassis bond). Printed cradles for the heatsink itself need ASA/ABS/PC/PA — PETG is marginal at 70–80 °C, PLA will slump; let printed parts hold Wagos and the fan | | SSR heatsink (alt, matches the Printables build) | Generic **black anodized SSR heat sink 80 × 50 × 50 mm, "10–40 A"** — ~2.2 K/W (Electrokit's figure), rated for ≤25 A relays, pre-tapped M4 at puck spacing, usually ships with screws (+ sometimes a pad). Sourced equivalent: **Phidgets 3955_0** (HF92B-80, 2.4 K/W, M4, DIN-clip back) | Amazon (uxcell / Twidec / Baomain / Taiss, ~$8–12) · Phidgets | Slightly better than HS251 but 80 mm long — ==check tray length==. No panel-mount holes: held by the puck screws through a bracket/cradle (ASA/ABS/PC if printed); ground lead from an M4 screw to chassis | | Thermal pad | Crydom **HSP-1** ($2.96) / **HSP-2** adhesive-backed ($2.16), or AutomationDirect **AD-SSR-THERM-PAD** (10-pack) | DigiKey · AutomationDirect | 0.006–0.008 in interface per Crydom | | Aux fuse | **McMaster 6986K636** (pack of 5, ~$20) — T 2 A 250 VAC 5×20 ceramic, UL Recognized, IEC 60127-2, listed as 215 / S505 equivalent; McMaster quotes 100 A breaking. Same part by name: Littelfuse **0215002.MXP** (1500 A I.R. on the datasheet) | McMaster-Carr · DigiKey | Ceramic on purpose: glass 5×20 time-lags (218/213 series) only interrupt 35 A | | Aux fuse holder | **McMaster 7087K43** — panel-mount 5×20 twist-cap, 250 VAC, 1/10–16 A, 0.25" straight QD tabs, UL Recognized, ~$14 (7087K44 for 90° elbow tabs) | McMaster-Carr | Panel ≤ 0.13"; D cutout 0.461" × 0.506" — drill 15/32" and file the flat so it can't spin. McMaster lists 215/216/217/218 and Bussmann S505 as compatible fuses. In-line alt: Littelfuse 01500520H (600 V / 20 A, 105 °C, 14 AWG leads) | | Master switch | illuminated rocker, ≥15 A / 125 VAC | — | DPST if you want N switched too | | E-Kill button | normally-open momentary, panel mount | — | wired across the RMP E-KILL terminals | | 5 V for RMP | USB-C wall adapter + panel pass-through, **or** Mean Well IRM-10-5 | DigiKey | IRM-10-5 hangs off the fused aux branch via ⟨L′⟩ / ⟨N′⟩; ==check RMP barrel size/polarity== | | Bay fan | **Noctua NF-A6x15 5V** (on hand) — 60 × 60 × 15 mm, 3500 rpm, 23.4 m³/h / 13.8 CFM, 2.43 mm H₂O, 0.17 A max, 3-pin, operating to 70 °C | — | Straight onto AUX1 (+5 V / −). Must pull room air in through the side vents, not recirculate the bay | | Thermocouples | the two supplied K-types to start; glass-braid or SS-sheathed ungrounded for long-term >190 °C | Adafruit 270 or similar | tips must not touch metal | | Wire | ≥14 AWG high-temp (silicone or fibreglass) for the element path; high-temp crimp terminals | — | reuse the factory sleeved leads and ceramic terminals where they reach | ## Power and bay cooling - RMP needs 5 V only. Its own 5 V output terminal is unprotected — don't hang anything else off it. - Bay fan: the stock DC fan cools the TRIAC/relay bay and, per the owner's guide, runs after cooking until the unit drops below 95 °F. The same job exists after the mod (SSR heatsink + RMP in that bay), so keep a fan there and give it AUX1 with "after run" cooling enabled in the profile. - If going the 12 V route: Mean Well IRM-10-12 (or IRM-20-12) + RM Fan Controller. If going 5 V: IRM-10-5 ([DigiKey](https://www.digikey.com/en/products/detail/mean-well-usa-inc/IRM-10-5/7704657)) can feed the RMP barrel jack and nothing else. ## Mounting - SSR + heatsink and the 5 V module go where the SharkNinja board was, in the bay fan's airflow. - RMP goes in the stock control-panel opening on the control side (the Printables housing above may fit; otherwise print the official case from the saved STEP files and panel-mount it). - Master rocker and E-Kill button on the same panel, reachable with the door open. # Configuration RMP settings to start with (firmware 3.x): - Profile: the default low-temperature lead-free paste for the first runs - AUX1 (bay fan): on during run, on for a cooling period after run - AUX2: off unless the convection fan is on a second SSR, then 100 % during run - Max-temp cutoff: set a little above the hottest profile's peak so a runaway trips it before the TCO has to - WiFi: `Setup WiFi` on the main menu → join the `RMPro` hotspot → pick the SSID → the menu button then shows the IP for the web UI - Calibration & Characteristics: run after the first successful profile to let the controller learn the oven's lag # Build procedure 1. Unplug. Photograph every connector and label every wire before cutting. 2. Map the elements: find every element terminal, measure each element's resistance (~25 Ω for a 583 W one), count top vs bottom, and write the combination that lands ≤ 1750 W in the table below. 3. Read the TCO rating (slide its sleeve back), find the lamp, read the fan motor and bay fan labels. 4. Remove the SharkNinja board and the stock NTC. Keep the sleeved leads and ceramic terminals. 5. Mount the SSR/heatsink, 5 V module, master switch, E-Kill button, and the RMP housing. 6. Wire the mains side per the table; crimp, sleeve, tie down, re-check the ground bond. 7. Wire the RMP side per the table; route the thermocouples. 8. Bench check with the elements disconnected: power the RMP, run Device Test or Bake at a low setpoint, confirm the SSR LED follows the output, confirm the E-Kill kills it. 9. Reconnect elements. First reflow with a blank PCB on the tray; watch whether the oven tracks the profile. If it lags, add insulation between cavity and shell before touching the algorithm. | Element | Location | Measured Ω | Calc W @ 120 V | On SSR? | |---|---|---|---|---| | E1 | | | | | | E2 | | | | | | E3 | | | | | | E4 | | | | | # Build Log ## 2026-11-09 - Side panel off; SharkNinja board, element terminals, fan motor and bay fan exposed and photographed - Traced the cord neutral: yellow lead → thermal cutoff clamped to the cavity wall (lower left) → white lead. TCO is in the neutral leg - ==Next: read the board's spade-tab silkscreen and record wire colour per tab before pulling the board== # Decisions - **One SSR for all selected elements** (vs. keeping the stock TRIAC board) - **Why**: the RMP expects a single SSR and PWMs it slowly (down to 1 Hz); the SharkNinja board has no external control input and its NTC is in the wrong place and too slow (EEVblog) - **Alternatives**: two SSRs (top/bottom) on SSR + AUX2 — not needed, the RMP only has one heater channel anyway - **Convection fan hardwired on** - **Why**: matches Ace's build which has run for years; forced convection evens out the cavity - **Alternatives**: AUX2 + second SSR for per-profile switching — can be added later without rewiring the element path - **Keep the factory TCO where it is (neutral leg) and the chassis ground** - **Why**: an SSR's failure mode is shorted-on; the TCO is the only thing that then stops the elements. In the neutral it still opens the whole circuit, and leaving the factory crimps and clamp alone avoids cooking a one-shot device while "improving" it - **Alternatives**: moving it to the line side between the switch and SSR — cleaner on paper, but means cutting factory crimps and re-terminating a part that is sensitive to heat # TODO - ==Count and measure the elements; fill in the table and pick the ≤ 1750 W set== - ~~Find the TCO~~ (found 2026-11-09 — neutral leg, clamped to the cavity wall, lower left) — ==read its rating off the body; the stock 500 °F broil mode already heats that wall harder than a 245 °C reflow peak, so it should hold== - ==Read the convection motor and bay fan labels (voltage, fan frame size)== - ==Measure cavity volume== - ~~Choose SSR and heatsink~~ (Teledyne SHC23D25 on hand; Crydom HS251 chosen 2026-11-09) — ==order HS251 + thermal pad, master rocker, E-Kill button, 5 V module or panel USB-C pass-through== - ~~Decide 5 V fan on AUX1 vs 12 V fan + RM Fan Controller~~ (Noctua NF-A6x15 5V on AUX1) - ==Verify the RMP barrel jack size/polarity if using the IRM-10-5== - ==Check whether the Printables housing fits the SP201 control-side opening== # References - [[Reflow Master Pro]] - [[Ninja SP101 reflow oven mod using Reflow Master Pro and an SSR – Ace's Electronics]] - [[Reflow Solder Paste]] - [reflowmasterpro.com](https://reflowmasterpro.com) — FAQ (oven ≤ 18 L / ≥ 1300 W, probe placement, SSR spec), Hardware Installation - [Reflow Master Pro schematic 2024-01](https://reflowmasterpro.com/files/RMP_Schematic_2024_01.pdf) - [Ninja FT205CO Owner's Guide](https://mobilecontent.costco.com/live/resource/img/static-us-pdf/9413025_UserManualandWarranty.pdf) - [EEVblog — Ninja SMT Reflow Oven](https://www.eevblog.com/forum/projects/ninja-smt-reflow-oven/) - [Amazon listing confirming SP201 = FT205CO](https://www.amazon.com/Ninja-Countertop-Extended-Capacity-Capability/dp/B09TD18SC5) # Changelog ## 2026-11-09 - Note created from the side-panel-off photo (`media/ninja-ft205co-side-panel-off.jpg`), the reflowmasterpro.com docs and 2024-01 schematic, Ace's SP101 clipping, the FT205CO owner's guide and the EEVblog Ninja thread. Wiring plan, parts candidates and build procedure drafted; element count and TCO still to be confirmed at the bench. - Later the same day: TCO located in the neutral leg — block diagram, mains table, decisions and TODO corrected (it had been drawn on the line side). Ace's wiring diagram embedded under Design. Build Log section added. - Colour-coded wiring diagram drawn (`media/ninja-ft205co-reflow-wiring.svg` + `.png`) and swapped in for the ASCII block diagram. - Added a fused auxiliary branch (T 2 A) for fan / lamp / 5 V module to the diagram and the mains table; removed the earlier "optional 15 A fuse" note (wrong fuse). - Specified the aux fuse (Littelfuse 0215002.MXP) and in-line holder (Littelfuse 01500520H); added a Parts list table under Design. - Holder switched to a panel-mount McMaster 7087K43 (changeable from outside, next to the master switch); the in-line holder kept as the alternative. - Fuse sourced as McMaster 6986K636 (215/S505-equivalent ceramic time-delay) so it ships with the holder; Littelfuse 0215002.MXP kept as the by-name equivalent. - SSR confirmed as Teledyne SHC23D25 and bay fan as Noctua NF-A6x15 5V (both on hand); heatsink sized and specified (Crydom HS251, HS172 alt) with thermal pad options. - Observations from the Printables build photo folded into Resources (generic black SSR heatsink + fan below, Wago 221 holders, internal 5 V module, TCO kept in neutral). - Heatsink alternatives added: generic 80 × 50 × 50 black SSR extrusion (the one in the Printables photo) and Phidgets 3955_0; DigiKey part numbers/prices recorded for HS251/HS172 and pads.