#electronics #connectors #molex #sherlock #crimping
# Overview
Molex Sherlock is a 2.00 mm pitch wire-to-board system. The 35507 crimp housings take **50212** open-barrel terminals (24–30 AWG). Those need a much smaller conductor crimp than Micro-Fit, so **the Micro-Fit tool (63819-0000) won't crimp them properly**.
# Configuration
## 50212 crimp spec
From the Molex 63819-0500 tool spec (ATS-638190500). Wire 24–30 AWG, insulation OD 0.80–1.40 mm, **strip 1.30–1.80 mm**.
| AWG | Conductor crimp H | Conductor W | Insulation crimp H × W | Min pull force |
|---|---|---|---|---|
| 24 | 0.51–0.61 mm | 1.02 mm | 1.43 × 1.40 mm | 29.4 N |
| 26 | 0.51–0.61 mm | 1.02 mm | 1.43 × 1.40 mm | 19.6 N |
| 28 | 0.51–0.61 mm | 1.02 mm | 1.31 × 1.29 mm | 9.8 N |
| 30 | 0.51–0.61 mm | 1.02 mm | 1.31 × 1.29 mm | 4.9 N |
Same conductor profile at every gauge, so the die to look for is **~1.0 mm wide, closing to ~0.5 mm**.
## Tools
| Tool | Dies | Verdict |
|---|---|---|
| **Molex 63819-0500** | 50212 + 59354, 24–30 AWG | The official tool. Also does Micro-Latch. Worth hunting used. |
| **Engineer PA-09** (Japan-made) | 1.0 / 1.4 / 1.6 / 1.9 mm | Best aftermarket match. 1.0 mm die closes to ~0.50 mm. |
| Engineer PAD-11 (S plate) | 0.7 / 1.0 / 1.3 / 1.6 / 1.9 / 2.2 mm | Same idea; 1.3 mm suits 28–30 AWG insulation. Swappable plates. |
| IWISS IWS-2820M | 0.7 / 1.0 / 1.3 / 1.6 / 1.9 / 2.2 mm | Budget PAD-11-style, spring-loaded, no ratchet. |
| IWISS IWS-3220M / 3220S, PEBA 1020M | Not published | ==Ratcheting one-squeeze; fit on 50212 unverified — test first.== |
| Engineer PA-24 | 1.3 mm smallest | No 1.0 mm die. Skip. |
| Molex 63819-0000 (Micro-Fit) | Smallest nest 0.70–0.80 × 1.10 mm | **No.** ~0.2 mm too tall; locator set for a 2.54–2.92 mm strip. |
## Technique
- Conductor barrel first in the **1.0 mm** die, then the insulation barrel in **1.4 mm** (24–26 AWG) or **1.3 mm** (28–30 AWG).
- Aftermarket tools have no locator, so position by eye. The short strip leaves little margin.
- Measure crimp height with a blade or point micrometer (calipers ride the seam), and pull-test a few on the actual wire against the table above.
# References
- [[Connector Crimping]] — general micro-terminal crimper notes
- [[Molex Micro-Fit 3.0 Connector Reference]] — covers the 63819-0000 tool ruled out here
- [Molex 63819-0500 spec sheet (ATS-638190500)](https://datasheet.eeworld.com.cn/view/14488862.html)
- [Molex 63819-0000 spec sheet (ATS-638190000)](https://70ic.com/666768/0638190000.pdf)
- [RS — Sherlock 35507 housing, takes 50212 terminals](https://uk.rs-online.com/web/p/wire-housings-plugs/7979149P)
- [Engineer PA-09 / PA-20 / PA-21 die widths (Duet3D forum)](https://forum.duet3d.com/post/119947)
- [PA-09-pattern die chart with die heights (Sierra IC)](https://sierraic.com/buy_online/download/datasheet/206952/10140)
# Changelog
## 2026-10-29
- Note created from research on whether the Micro-Fit tool works on Sherlock terminals and which aftermarket crimpers fit 50212.