#voron #voroncascade #cnc #electronics #layout #ueb # Overview **Current revision: Layout J (2026-11-15)**, fitted against wiring Rev O. The letter is in the frontmatter, and the [[#Changelog]] lists what each letter changed. Where everything sits in the Voron Cascade's electronics bay: two DIN rails on the gantry plate, the mains terminals on a rail on the back panel, the line filter on the floor, and the operator controls in the front and top panels. This is the placement that [[Voron Cascade Electronics Wiring]] defers to. That note says what connects to what; this one says where each part goes, what it clears and what has to be drilled. The settings are in [[Voron Cascade Electrical Configuration]] and the open checks in [[Voron Cascade Bench Checks]]. Layout J is layout I with one change, on the rear rail: the PE group has one grounding block, at its right-hand end (block 11), where layout I had two at its left (blocks 5 and 6). No part moves and no dimension changes. Layout I was layout H brought up to date with everything decided, measured and cut from 2026-11-11 to 2026-11-14; [[#Changes since layout H]] lists that. - **Plate rails.** The upper rail carries the FlexiHAL and Pi, the MDR-60, K2 to K5, F1 and F2, XT3 and KM1. The lower rail carries the three drivers, the NDR-480, the SDR-120 and the VFD on a printed mount. Each has its own grounding block. - **Rear rail.** 119 mm, cut, with 15 blocks: XT1, the seven-block PE group and XT2. - **Fit test.** Zero collisions across the 22 placed parts, the frame, the fan, the inlet and the wire guard. Layout J moves nothing, so the result is layout I's. - **To drill.** Four M5 holes for the lower rail and one 10-32 bonding stud in the plate, four filter holes in the bottom panel, two front-panel holes opened to 16 mm and one cable hole in the top panel. This note is the layout's home from J on. Layouts H and I were published pages, which stay as the record of those two layouts ([[#References]]). The figures here are PNG renders made in Claude's workspace by the scripts behind those pages; the scripts are not in the vault. ==Items in this highlight style are unmeasured or still to do.== # Design ## The layout Positions use the same bay coordinates as the earlier layouts: `a` from the inside of the front panel (0) to the back panel (420), `h` above the floor panel, `d` out from the gantry plate toward the door. In the Cascade CAD, `y = a − 59`, `z = h − 72.9`, `x = d + 259`. ![[media/cascade-layout-legend.png]] ![[media/cascade-layout-elevation.png]] *Elevation, looking at the gantry plate from the door. Upper rail on its stock holes at h 257, lower rail at h 102. The mains terminals are on the back panel and are seen end-on.* ![[media/cascade-layout-plan.png]] *Plan, looking down. Solid parts are the lower row; dashed outlines are the upper-rail parts above them.* ### Upper rail, front to back - **FlexiHAL** a 24 to 151, then the **MDR-60** a 157 to 197. - **K2, K3, K4, K5** a 202 to 226.8, then an 8 mm end stop. - **F1 and F2** a 234.8 to 250.8. - **XT3,** 12 blocks and an end section, a 250.8 to 325.6, then an end stop to a 333.6. XT3 sits over the VFD, 28.4 mm above its top. - **KM1** a 340 to 385, then the **grounding block** a 386 to 392. The rail ends at a 398. ### Lower rail and floor - **Drivers** at 31 mm pitch: U2 a 23, U3 a 54, U4 a 85, with 7.5 mm between cases. - **NDR-480** a 113.5 to 199 and **SDR-120** a 204 to 244. - **Grounding block** a 248 to 254. The rail runs on under the VFD and ends at a 352. - **VFD** on a printed rail mount at a 257 to 347, h 55.6 to 205.6, 5 mm lower than in layout H. Its back is 13.5 mm off the plate with the mount drawn 6 mm thick. - **Filter** on the floor under the VFD. - **Rail screws** at a 40, 140, 240 and 340, all at h 102. The lower grounding block, with the drivers at 31 mm pitch, was decided on 2026-11-13. The alternative that was set aside kept the 33 mm pitch: leave the lower grounding block out and bond that rail with a paint-piercing washer under one rail screw. The space between the SDR-120 and the VFD is then 9 mm, which takes the block only with 1.5 mm each side. ## Fit-test results | Check | Result, mm | |---|---| | Collisions among the placed parts | 0 | | NDR-480 air above / below / side | 38.6 / 19.4 / 5.0 (1.4 and 0.6 short of 40 / 20) | | SDR-120 air above / below / side | 46.9 / 19.4 / 4.0 (4.0 to the grounding block) | | MDR-60 air above / below / side | 26 to the top panel / 47.4 / 5.0 (short of 40 above) | | Depth: NDR-480 / SDR-120 / MDR-60 / KM1 / VFD to the door | 18.5 / 32.5 / 54.5 / 53.2 / 36.0 | | Driver to driver / last driver to NDR-480 | 7.5 / 5.0 | | Driver tops to the FlexiHAL | 42 | | Relays to the SDR-120 below / to the top frame member above | 46.9 / 7.5 | | XT3 to the VFD's top below / to the top frame member above | 28.4 / 30.0 | | Upper group end stop to KM1 | 6.4 (5.2 to 7.2 by end-cover width) | | KM1 to the fan / to the wire-guard nut below / to the VFD's top below | 15.0 / 9.7 / 13.6 | | Upper grounding block to the fan / spare rail behind it | 8.0 / 6.4 | | Lower grounding block to the SDR-120 / to the VFD | 4.0 / 3.0 | | VFD to the filter below / to the wire-guard nut | 17.0 / 7.9 | | Lower rail's new end to the bonding stud's centre / rail edges to the M6 bolt heads below and above | 14.0 / 4.1 and 25.1 | | Rear terminal row to the VFD / to the breaker below / to the wire-guard hole above | 25.0 / 33.5 / 31.5 | | Cable exit between the rear terminal row and KM1 | 75.7 high | | Rear terminal row to each end of its rail / rail ends to the uprights | 3.6 / 0.3 and 0.7 | **Upper rail gap.** With the 8 mm end stops in hand the group takes 113.0 mm of the 119.4 between K4 and KM1 and leaves 6.4. That takes the end cover at the 2.8 mm Entrelec lists for it. A 2 mm cover leaves 7.2 and a 4 mm one 5.2. The cover is the one width still unmeasured. If it comes up short, KM1 can slide back about 6 mm before the grounding block behind it reaches the end of the rail. **Blocks.** The 7641K51 and 7641K81 are taken as Entrelec M 4/6 and M 4/6.P: 6 mm wide, 44.5 mm top to bottom, 48 mm out from the plate on a 7.5 mm rail. The KN-F10L24DC fuse terminals use the plain KN-F10 envelope. **Margins that depend on parts not yet measured.** The VFD can be up to 98 mm wide before it overlaps the wire-guard nut. On its mount it would pass about 6 mm in front of the nut, which stands 7.2 mm off the plate, but the machine's cables come in there. That side then sits 17 mm from the rear terminal row. Its front edge is 3 mm from the lower grounding block, so check the real hole-to-edge distance. The printed driver mounts can be up to 26 mm wide, which leaves 5 mm between mounts and 3.75 mm to the NDR-480. ## The rear rail The rail is cut: 119 mm, on the two stock holes in the back panel. It carries 15 blocks, one more than layout H: the PE group grew from six blocks to seven. | Block | Net | Block colour | What lands on it | |---|---|---|---| | 1, 2 | XT1 L, jumpered | Black | Breaker L out · SDR-120 L · MDR-60 L · KM1 1L1 | | 3, 4 | XT1 N, jumpered | White | Breaker N out · SDR-120 N · MDR-60 N · KM1 5L3 | | 5 | PE, jumpered 5 to 10 | Green | Plate stud · 2020 frame lug | | 6 | PE | Green | Incoming earth from the inlet · lower-rail grounding block | | 7 | PE | Green | SDR-120 FG · gantry jumper | | 8 | PE | Green | MDR-60 FG · NDR-480 FG | | 9 | PE | Green | Filter ground post · VFD PE | | 10 | PE | Green | Upper-rail grounding block · wire link to block 11 | | 11 | PE | Grounding block, 7641K81 | Wire link from block 10 · one spare screw | | 12, 13 | XT2 L-SAFE, jumpered | Red | KM1 2T1 · NDR-480 L · filter L · one spare | | 14, 15 | XT2 N-SAFE, jumpered | White | KM1 6T3 · NDR-480 N · filter N · one spare | Block 11 clamps to the rail and bonds it. The green blocks' jumper bar does not fit it, so a 12 AWG wire links block 10 to block 11. The incoming earth and every device earth land on the six jumpered green blocks, so they meet in copper and none of them depends on that link. ==The six green blocks need one jumper bar that spans all six.== A separator plate goes between blocks 11 and 12, where the PE group meets the switched side. N and N-SAFE are both white and must never be bridged, because KM1 switches the neutral too. | Row | 15 blocks | End stops | Cover, separator | Total | Spare on 119 mm | |---|---|---|---|---|---| | As drawn: 2.8 mm cover | 90 | 2 × 8 | 2.8 + 3 | 111.8 | 7.2 | | With a 2 mm cover | 90 | 2 × 8 | 2 + 3 | 111.0 | 8.0 | ### The rail as cut - **Same two holes,** at d 40.3 and d 119.3. Centred on them, the rail runs from d 20.3 to d 139.3. - **It fills the space between the uprights,** which leave 120 mm. That is about half a millimetre at each end. - **The row is centred too,** from d 23.9 to d 135.7, with 3.6 mm of rail showing at each end. - **Keep both end stops.** The uprights would stop the row sliding off, but the end stops are what clamp it together. ### Space and access - **Row envelope:** 46 mm top to bottom and 48 mm out from the panel, at h 97.5 to 143.5. - **The block fronts face the side of the VFD** from 25 mm. From the door the row is seen end-on. - **Wire entry:** 33.5 mm below the row to the breaker and 31.5 mm above it to the wire-guard hole, for 30 clamps. L and N are 14 AWG and PE is 12 AWG, one conductor per screw. - **Wire it with the back panel off,** or before the VFD goes on. The screws are hard to reach afterwards. ## Bonding points | Point | Where | Notes | |---|---|---| | Steel plate stud | Tapped 10-32 at a 366, h 120.5 | Level with the rear rail and 6 mm in front of the block faces, with a straight line in from the door. Open behind the plate. Its wire lands on block 5. | | Upper rail | 7641K81 at a 386 to 392 | Takes the 24 V 0 V bond. XT3's last block is 63 mm away, past KM1. Fed from block 10. | | Lower rail | 7641K81 at a 248 to 254 | Takes the 48 V −V bond. Next to the SDR-120, 49 mm from the NDR-480. Fed from block 6. | | Rear rail | Block 11 of the row | One 7641K81 at the right-hand end of the PE group, linked to block 10 by a 12 AWG wire. The incoming earth lands on block 6. | | 2020 frame lug | Rear upright on the plate side, door-facing slot, h 160 | 16.5 mm above the terminal row and below the cable mount. Its wire lands on block 5. This is the bay's own frame; measure from it to the base frame and add a second lug outside the bay if that reads over 0.1 Ω. | | VFD | Its PE terminal wire, to block 9 | The printed rail mount keeps the case off the plate, so this wire is the VFD's only earth. Until 2026-11-14 a washer under a mounting bolt bonded it to the plate as well. | | Gantry | Outside the bay, through the drag chain | High-strand 12 AWG from block 7. See the drag chain. | **Wire.** Every bonding jumper is 12 AWG green/yellow, the size for the 20 A branch breaker. The one exception is the 48 V −V bond, which stays 18 AWG (accepted 2026-11-14). Layout H assumed 14 AWG. **Masking before powder coat.** On the steel plate, mask the upper rail footprint (a 24 to 398, h 239.5 to 274.5), the lower rail footprint (a 21.5 to 352, h 84.5 to 119.5) and a pad around the stud. The rear rail is on the back panel, not the plate, so there are two rail footprints to mask, not three. The gantry, bed and carriage lugs are outside the bay. ## Panel views The four enclosure panels as they stand in layout J. Panel holes, the fan, inlet and cable mounts are taken from the Cascade CAD. Solid shapes are fixed to the panel shown. Dashed outlines are parts on the gantry plate that stand in front of it. ### Back panel · from inside the bay ![[media/cascade-layout-back-panel.png|430]] *Looking toward the back of the machine, gantry plate on the left. The row is drawn in the block colours: black XT1 L, white N, green PE with the grounding block, block 11, striped yellow, red XT2 L-SAFE, white N-SAFE. Block 1 is at the plate end; the order can be mirrored.* ### Front panel · from inside the bay ![[media/cascade-layout-front-panel.png|430]] *Looking toward the front of the machine, so the door is on the left. POWER ON is in the hole nearest the door and AIR in the one nearest the plate; the middle hole is plugged. The E-stop body hangs from the top panel behind them. The AIR button's terminals end 3 mm short of the FlexiHAL.* ### Bottom panel · from above ![[media/cascade-layout-bottom-panel.png]] *Looking down at the floor. The filter and the air-inlet cover are fixed to this panel; the lower-row parts hang above them. The four filter slots are the only new holes here.* ### Top panel · from above ![[media/cascade-layout-top-panel.png]] *Looking down through the top panel at the upper-rail parts below it. The two-button box sits on top of the panel beside the E-stop, which is in its stock hole. The front buttons and the E-stop body are below the panel.* - **Back panel:** nothing new to drill. From the top down it carries the fan and two keystone positions, the terminal row, then the inlet and breaker. - **Bottom panel:** the filter needs four holes for its mounting slots, on a 50.8 × 95.3 mm pattern. Mark them from the filter itself; the drawn positions are approximate. - **Front panel:** the left and right holes are opened to 16 mm and the middle one gets a plug. Nothing else changes. - **Top panel:** one new cable hole under the control box. The E-stop keeps the stock hole. The upper-rail parts end 25 to 50 mm below the panel. - **WAGO mounts:** none of the three printed mounts is used. The one on the rear bottom frame member would have overlapped the filter by 2.8 mm. ## Operator controls Approved on 2026-11-11 and unchanged since. There are four buttons, the E-stop and one spare hole. The hardware chain is the E-stop and POWER ON only. There is no POWER OFF button: routine off is the E-stop button on the touchscreen, and the physical E-stop is the hard off. ### The arrangement on the full machine ![[media/cascade-layout-operator-controls.jpg]] *Left: standing in front of the machine. Right: the front right corner. The machine is the Cascade CAD. The box, the buttons and the bay contents are simple stand-ins at their real sizes, and the print colours are placeholders.* | Control | Part | Where | Hole | What it does | |---|---|---|---|---| | E-stop | GCX1131, 22 mm | Top panel, stock hole: a 55.5, d 99.5 | Existing Ø22 | Hard off. One contact in the latch chain, one in the HALT loop | | CYCLE START | Adafruit 1440, 16 mm, green | Box on the top panel: d 29 | In the box | Resume only, to begin with. Lamp flashes while paused, steady while running | | FEED HOLD | Adafruit 1441, 16 mm, yellow | Box on the top panel: d 59 | In the box | Pause only. Lamp lit while paused | | POWER ON | Adafruit 1479, 16 mm, white | Front panel, right-hand hole: d 120, h 289.5 | Ø10 opened to 16 | Arms the hardware latch. Lamp lit while latched | | AIR | Adafruit 1477, 16 mm, blue | Front panel, left hole: d 40, h 289.5 | Ø10 opened to 16 | Toggles the air blast through LinuxCNC, in step with M7 and M9 | | AUX | None yet | Front panel, middle hole: d 80, h 289.5 | Plugged | No function and no input yet | ### Front panel - **Depth of the 16 mm buttons.** Adafruit's drawing gives 24.0 mm from the panel's outer face to the terminal tips. Through the 3 mm panel that is 21 mm inside the bay. - **AIR is in line with the FlexiHAL,** which starts 24 mm in, so its terminals end 3.0 mm short of it. Solder its leads and fold them sideways. A straight quick-connect does not fit. - **POWER ON has room.** Its terminals end 14.5 mm in front of the E-stop body that hangs from the top panel. - **On the outside** the bezels are 18 mm square and sit 8.7 mm above the touchscreen's top edge. Nothing overlaps the screen. ### Top panel - **The box is a placeholder:** 56 wide, 43 high and 56 mm deep, with a face leaning back 30°. It runs from d 16 to d 72, with its front at a 20, just behind the printed corner cap. - **Buttons at 30 mm pitch.** At 40 mm the box would run under the E-stop head. - **Clearances:** 7.5 mm from the box to the E-stop head, 19 mm to the enclosure handle and 1.2 mm to the panel screw at a 30.5, d 10. - **It needs a new cable hole** in the top panel under the box. The stock hole is the E-stop's again. - **A printed top plate is planned** to carry the box and move the E-stop about 10 mm toward the door. That would open the gap between them to 17.5 mm. The E-stop body reaches the door-side frame member at a shift of 25 mm. ### How the wiring note does it, at Rev O [[Voron Cascade Electronics Wiring]] is the authority for this list. It is repeated here because the layout was fitted against it. - **Latch chain:** the E-stop contact, then POWER ON in parallel with the K3 seal-in. There is no POWER OFF contact. - **HALT loop:** the E-stop's second contact alone. - **CYCLE START:** a normally-open contact on the FlexiHAL's `Start` input. It acts once per fresh press, and only while a program is paused. Its lamp is on `Aux2`. - **FEED HOLD:** the `Pause` input, pause only. Its lamp is on `Aux1`. - **AIR:** a normally-open contact on `Aend`. Each fresh press switches mist on or off in LinuxCNC, with the machine on. Its lamp comes from K4 14, the switched side of the valve feed. - **Air valve:** its feed runs through KM1's normally-open auxiliary contact, 13 and 14. Any trip that drops the contactor closes the valve. - **Power present:** KM1's normally-closed auxiliary contact, 21 and 22, tells LinuxCNC whether the contactor is in. Machine-on is refused until it is. Since 2026-11-14 the contactor dropping out by itself also puts LinuxCNC into E-stop, and the E-stop cannot be reset on the screen while the contact still reads "in". - **AUX:** nothing to wire yet. `Aux3` stays spare for its lamp. - **Screen off:** K2 follows LinuxCNC's E-stop latch. The on-screen E-stop drops the contactor, and an E-stop-button trip keeps drive power off until it is reset on the screen. "Machine off" leaves the drives powered. - **Door:** since 2026-11-15 the two door switches only tell LinuxCNC, through K5 and the `Door` input. With the spindle on, opening the door stops the spindle and aborts the program, and the machine stays on. With the spindle off it does nothing, so the axes can be jogged and a probe used with the door open. The door no longer cuts drive power. No part moves; one wire at K5 does. - **Lamp resistors:** 4.7 kΩ in series with each button LED on 24 V, about 4.5 mA. - **POWER ON's contact** briefly switches up to about 0.4 A of coil current. Adafruit publishes no contact rating, so it is a bench check. - **Wire:** the front-panel buttons and the E-stop get 20 AWG blue for each contact and lamp feed and 18 AWG white/blue for each return. The top box has one 6-core cable through the new hole under it. - **The Aux pull-ups come off.** The FlexiHAL's four `Aux` outputs each have a 1 kΩ pull-up, measured on 2026-11-14. They are removed before anything is wired, and K2 and the two top-box lamps stay on the outputs listed here. No part changes place. Button data: [Adafruit 16 mm illuminated pushbutton](https://www.adafruit.com/product/1477) and its [dimension drawing](https://cdn-shop.adafruit.com/datasheets/R16diagram.jpg). ## The drag chain The chain carries one motor cable, one encoder cable, one endstop cable and the PE jumper, with a small air line to follow. The PE jumper is 12 AWG, which was the only change here since layout H. It still fits. | In the chain | Assumed diameter, mm | Area, mm² | |---|---|---| | Motor cable, RVV 4 × 0.5 mm² | 6.4 | 32.2 | | Encoder cable, RVVP 6 × 0.2 mm² | 5.6 | 24.6 | | Endstop cable | 4.0 | 12.6 | | PE jumper, 12 AWG high-strand | 4.4 | 15.2 | | **Four cables** | 20.4 side by side | 84.6 | | Air line, later | 4.0 or 6.0 | 12.6 or 28.3 | | Chain, inner size | Four cables | With a 4 mm air line | With a 6 mm air line | |---|---|---|---| | 10 × 20, 200 mm² | 42% (fits) | 49% (only stacked, 0.4 mm of height spare) | 56% (does not fit) | | 15 × 15, 225 mm², as on the BOM | 38% (fits) | 43% (fits) | 50% (fits) | - **In the 10×20 chain the two thin cables share a column.** The endstop cable on the PE jumper is 8.4 mm of the 10 mm height. The four cables then take 16.4 mm of the 20 mm width. - **A 4 mm air line no longer fits beside them.** Only 3.6 mm of width is left. It can ride on the encoder cable, which uses 9.6 mm of the 10 mm height. - **A 6 mm air line does not fit the 10×20 chain.** On top of the PE jumper it would need 10.4 mm of height, and beside the cables the row needs 22.4 mm. - **The 15×15 chain takes everything in two layers:** motor and encoder cables below at 12 mm wide, the rest above at up to 14.4 mm, 12.4 mm high in all. - **The jumper's diameter depends on the wire.** It is taken as 4.4 mm. A 65-strand MTW is nearer 3.9 and a silicone-insulated lead nearer 4.5. Either way a 4 mm air line is a tight fit and a 6 mm one does not go in. - **The other diameters are typical values** for those cable types, not measurements. The kit cables are in hand, so a caliper settles it. ## Drill and tap list | For | a | h | Thread | Behind the plate | |---|---|---|---|---| | Lower rail | 40 | 102 | M5 tapped | Open to the machining side | | Lower rail | 140 | 102 | M5 tapped | Open to the machining side | | Lower rail | 240 | 102 | M5 tapped | Front-brace cover, hollow here | | Lower rail | 340 | 102 | M5 tapped | Upright's T-slot, between the M6 bolts at h 75 and h 150 | | Bonding stud | 366 | 120.5 | 10-32 tapped | Open, behind the gantry back panel | | Upper rail | 85, 365 | 257 | existing holes | As stock | | Rear rail, on the back panel | d 40.3, d 119.3 | 120.5 | existing holes | As stock | ### Marking jig for the lower-rail holes ![[media/cascade-lower-rail-jig.svg]] *One flat printed plate, turned over between the two bottom corners of the frame opening. From the left corner it marks the holes 20 and 120 mm from the left post. Turned over, it marks the ones 160 and 60 mm from the right post. All four are 82 mm above the bottom extrusion. The jig is open underneath so it clears the bolt heads in both corners. The drawing and a 1:1 DXF are `media/cascade-lower-rail-jig.*`.* - **Lower-rail spacing.** The four screws are 100 mm apart so that they land on a rail slotted at 25 mm pitch. The rail's left end is at a 21.5, so cut it with a slot centred about 18.5 mm from that end. - **The jig.** A flat plate 5 to 6 mm thick. The suggested outline is a bar on two legs, and the drawing gives every keep-out from each corner so that the shape can change. The drawing (Rev C) labels the four holes H1 to H4 from the left; H2, at a 140, is the optional middle screw, and the jig's fourth bore, R2, is for H4. - **Where the positions come from.** `media/cascade-lower-rail-jig.py` writes the drawing (SVG and PNG) and the DXF (mm, origin at the corner of the left post and the bottom extrusion), for importing into CAD as a sketch. The positions come from the Cascade CAD and the plate DXF, not from the frame as built: each end hole is set from its own corner, so any error in the 380 mm opening ends up in the 200 mm between the holes at a 40 and a 240. - **Check the marks before drilling.** The left hole should sit 18 mm left of and 28 mm above the first driver hole. The hole at a 240 should sit 7 mm right of and 20 mm above the stock VFD hole. The hole at a 340 should sit in line with the two M6 bolt heads there, 27 mm above the lower one. - **Behind the rail hole at a 240** the printed front-brace cover is hollow, about 27 mm deep. Chips collect inside it and nothing has to come off. - **The rail hole at a 340 runs into the upright's T-slot,** which is about 9 mm deep, so use a drill stop and a short screw. The M6 bolts at h 75 and h 150 are anchored in the same slot: check that nothing sits in it behind the hole before tapping. The two M8 bolt heads in that slot are higher up, from h 173.9. - **Keep new holes out of a 295 to 355** unless they are on a 310 or a 340. The gantry upright is directly behind the plate there, and only its two T-slots leave room for a screw tip. - **Keep them above h 56.** The base extrusion is behind the plate below that. - **Thread length.** M5 in 3 mm steel is under four threads. That is enough for a rail held by four screws. Keep the screw short at a 340, where the tip runs into the upright's T-slot. - **Old holes.** Nine driver holes and the two stock VFD holes go unused. Seven of the driver holes open straight into the machining area, so plug them. - **Bottom panel.** Four holes for the filter's mounting slots; see the panel views. - **Front panel.** Open two of the Ø10 holes at h 289.5 to 16 mm: d 40 for AIR and d 120 for POWER ON. Plug the one at d 80. Adafruit's cutout is a 16 mm circle with a flat 15 mm across; in a plain round hole only the nut stops the button turning. - **Top panel.** One cable hole under the control box, about 12 mm, placed once the box is designed. The drawings show it at a 62, d 60. ### Rails - Upper: a 24 to 398, 375 mm, as in the Cascade CAD. The parts span 368 mm, so the BOM's 350 mm piece is too short for it. - Lower: a 21.5 to 352, 330.5 mm. It carries the VFD since 2026-11-14. - Rear: 119 mm, already cut. - Stock: 119 + 330.5 is 449.5 mm, more than the BOM's 350 mm piece. If the rear rail came from that piece, about 230 mm is left, which is too short for the lower rail. The upper rail needs its own piece anyway, so a 1 m length covers both. ### Printed driver mounts - Driver upright, narrow side to the rail, centred on the rail: h 43 to 161. - No wider than 26 mm, at 31 mm pitch. - Rail plus mount no more than 18 mm thick, which puts the driver terminals 105 mm from the plate. ## The H100 on the lower rail Decided on 2026-11-14: the VFD hangs on the lower rail on a printed mount, instead of on two screws tapped into the plate. The rail is one 330.5 mm piece from a 21.5 to 352, fixed at a 40, 140, 240 and 340, and the grounding block stays at a 248 to 254. The VFD's body is where it was, so the rail crosses its lower third. ### Reference for the printed mount ![[media/cascade-vfd-rail-mount-ref.svg]] *The body's top edge is 86.1 mm above the rail's top edge, and its bottom edge 28.9 mm below the rail's bottom edge. The upper-right hole is 79.55 mm above the top edge and the lower-left hole 22.45 mm below the bottom edge, 77 mm apart across. The drawing and a 1:1 DXF are `media/cascade-vfd-rail-mount-ref.*`, written by the `.py` beside them; the DXF's origin is the rail centreline at the VFD's left edge.* | | From the rail's nearer edge | From the rail centreline | h | |---|---|---|---| | VFD top edge | 86.1 above the top edge | +103.6 | 205.6 | | Upper-right hole | 79.55 above the top edge | +97.05 | 199.05 | | Rail top edge | | +17.5 | 119.5 | | Rail bottom edge | | −17.5 | 84.5 | | Lower-left hole | 22.45 below the bottom edge | −39.95 | 62.05 | | VFD bottom edge | 28.9 below the bottom edge | −46.4 | 55.6 | - **Keep the mount inside the VFD's outline.** Around the body there is 3 mm to the grounding block, 7.9 mm to the wire-guard nut, 17 mm to the filter below and 13.6 mm to KM1 above. - **Depth.** The rail is 7.5 mm deep. A mount of thickness t puts the VFD's face 117.5 mm plus t from the plate and leaves 42 mm less t to the door (it was 44.5 mm on the spacers). The drawings here take t as 6 mm, which puts the VFD's face 36 mm from the door. - **Bolt heads behind it.** Two M6 button heads on a 340 stand 2.9 mm off the plate, at h 75 and h 150. The lower one is 4.1 mm below the rail's bottom edge, where a latch would sit. - **Earth.** A printed mount keeps the VFD's case off the plate, so its PE terminal wire is its only earth. - **The body and hole pattern are the CAD's block.** The two holes are at a 263 and a 340, 77 mm apart across and 137 mm apart up: the lower-left one 6 mm in from the body's left edge, the upper-right one 7 mm in from its right edge and directly above the rail screw at a 340. Measure the H100 first. If the pattern differs, keep the body where it is drawn and move the mount's holes. - **The back of the H100.** If it is a bare heatsink, leave it open to the air or print the mount in a material that takes the heat. - **What goes away:** the two tapped VFD holes, the 5 mm spacers and the VFD marking jig. `media/cascade-vfd-jig.*` stays in the vault as the record of the bolted mounting. The bonding stud, which that jig could also mark, is 34 mm from the right post and 100.5 mm above the bottom extrusion. ## Positions for CAD | Part | Where | a (front→back) | h (height) | d (depth) | To door | |---|---|---|---|---|---| | U2 driver | backplane, low | 23.0 – 46.5 | 43.0 – 161.0 | 0.0 – 105.0 | 54.5 | | U3 driver | backplane, low | 54.0 – 77.5 | 43.0 – 161.0 | 0.0 – 105.0 | 54.5 | | U4 driver | backplane, low | 85.0 – 108.5 | 43.0 – 161.0 | 0.0 – 105.0 | 54.5 | | NDR-480-48 | backplane, low | 113.5 – 199.0 | 39.4 – 164.6 | 0.0 – 141.0 | 18.5 | | SDR-120-24 | backplane, low | 204.0 – 244.0 | 39.4 – 164.6 | 0.0 – 127.0 | 32.5 | | PE lower | backplane, low | 248.0 – 254.0 | 79.0 – 125.0 | 0.0 – 48.0 | 111.5 | | FlexiHAL + Pi 5 | backplane, high | 24.0 – 151.0 | 203.2 – 304.8 | 0.0 – 55.0 | 104.5 | | MDR-60-5 | backplane, high | 157.0 – 197.0 | 212.0 – 303.8 | 0.0 – 105.0 | 54.5 | | K2 | backplane, high | 202.0 – 208.2 | 211.5 – 302.5 | 0.0 – 78.5 | 81.0 | | K3 | backplane, high | 208.2 – 214.4 | 211.5 – 302.5 | 0.0 – 78.5 | 81.0 | | K4 | backplane, high | 214.4 – 220.6 | 211.5 – 302.5 | 0.0 – 78.5 | 81.0 | | K5 | backplane, high | 220.6 – 226.8 | 211.5 – 302.5 | 0.0 – 78.5 | 81.0 | | End stop A | backplane, high | 226.8 – 234.8 | 234.0 – 280.0 | 0.0 – 48.0 | 111.5 | | F1 | backplane, high | 234.8 – 242.8 | 235.0 – 299.0 | 0.0 – 46.0 | 113.5 | | F2 | backplane, high | 242.8 – 250.8 | 235.0 – 299.0 | 0.0 – 46.0 | 113.5 | | XT3 strip | backplane, high | 250.8 – 325.6 | 234.0 – 280.0 | 0.0 – 48.0 | 111.5 | | End stop B | backplane, high | 325.6 – 333.6 | 234.0 – 280.0 | 0.0 – 48.0 | 111.5 | | KM1 contactor | backplane, high | 340.0 – 385.0 | 219.2 – 294.8 | 0.0 – 106.3 | 53.2 | | PE upper | backplane, high | 386.0 – 392.0 | 234.0 – 280.0 | 0.0 – 48.0 | 111.5 | | H100 VFD | backplane, low | 257.0 – 347.0 | 55.6 – 205.6 | 13.5 – 123.5 | 36.0 | | Z1 line filter | floor | 250.0 – 380.5 | 0.0 – 38.6 | 27.0 – 132.1 | | | Mains terminals | back panel | 372.0 – 420.0 | 97.5 – 143.5 | 23.9 – 135.7 | | ## Changes since layout H Layout I made these changes on 2026-11-13 and 2026-11-14. Layout J changed the PE group row again on 2026-11-15; the other rows are as layout I left them. | Item | Layout H | Layout J | Why | |---|---|---|---| | Rear rail length | 115 mm, proposed | 119 mm, as cut | Cut to sit in the 120 mm between the uprights. | | Rear rail row | 14 blocks, 102 to 110 mm | 15 blocks, about 112 mm | The longer rail and 8 mm end stops left room for a fifteenth block. Decided 2026-11-13. | | PE group | Block 5 grounding, blocks 6 to 10 green, all on one jumper bar | Blocks 5 to 10 green, on one jumper bar. Block 11 grounding. A 12 AWG wire links 10 to 11 | The jumper bar does not seat in the 7641K81, checked on the part 2026-11-12. Layout I had two grounding blocks, at 5 and 6. Erik went back to one on 2026-11-15 and put it at the right-hand end. | | XT2 | Blocks 11 to 14 | Blocks 12 to 15 | Moved up by the extra PE block. | | Bonding wire | 14 AWG | 12 AWG, high-strand to the gantry. The 48 V −V bond is 18 AWG | Sized for the 20 A branch breaker. Rev M, 2026-11-12. The exception was accepted on 2026-11-14. | | End stops | 9 mm drawn, 8 to 10 possible | 8 mm, McMaster 5575N22 | The parts in hand. | | F1, F2 and XT3 | a 235.8 to 326.6, 4.4 mm spare | a 234.8 to 325.6, 6.4 mm spare | Follows from the 8 mm end stops. | | Relay order | K3, K2, K4, K5 | K2, K3, K4, K5 | Matches the wiring note's terminal drawing. The group stays at a 202 to 226.8. Decided 2026-11-13. | | Lower-rail screws | a 40, 135, 230 | a 40, 140, 240 and 340 | 100 mm apart for a rail slotted at 25 mm pitch, decided 2026-11-13. The fourth screw came with the longer rail on 2026-11-14. | | VFD height | h 60.6 to 210.6 | h 55.6 to 205.6 | The upper-right screw hole ran into an M8 bolt head behind the plate. Decided 2026-11-13. | | VFD mounting | Two M5 holes tapped in the plate, a 263, h 67.1 and a 340, h 204.1, with 5 mm spacers | A printed mount on the lower rail. The same two holes, 5 mm lower, are in the mount | Erik's decision, 2026-11-14. Nothing is tapped for the VFD, and its case no longer touches the plate. | | Lower rail | a 21.5 to 255, 233.5 mm | a 21.5 to 352, 330.5 mm | It carries the VFD. | | VFD face to the door | 44.5 mm | 36 mm, with a 6 mm mount | The rail is 7.5 mm deep where the spacers were 5. | | VFD to the wire guard | 12 mm, to the fitting | 7.9 mm, to its nut | A correction: the nut is 39.2 mm across and stands 7.2 mm off the plate. | | Drag chain | 14 AWG earth jumper, 40% full | 12 AWG earth jumper, 42% full | Follows from the bonding wire size. | | KM1 auxiliary contacts | Normally-closed pair unused | Normally-open pair in the valve feed, normally-closed pair reports power present | Rev M. Both are built into KM1, so nothing is added to the rail. | | Rail stock | One 350 mm piece gives the lower and rear rails | 119 + 330.5 = 449.5 mm, so it no longer does | The rear rail grew by 4 mm and the lower rail by 97. | Nothing else has moved. The drivers, the three supplies, the FlexiHAL, KM1, the filter, the plate stud, the frame lug and all the operator controls are where layout H put them. # TODO Check before drilling: - ==**The VFD's real size and hole pattern.** Everything here uses the 110 × 90 × 150 mm block from the Cascade CAD, with mounting holes 77 mm apart across and 137 mm apart up. Measure the unit before printing the mount. Keep the body where it is drawn and move the mount's holes to suit.== - ==**The mount's thickness.** It is drawn as 6 mm. Each millimetre more comes off the 36 mm between the VFD and the door.== - ==**The end cover.** The end stops are known now, at 8 mm. Measure the end cover: it decides whether the upper group has 5 or 7 mm to spare.== - ==**The rail's slot pitch.** The lower-rail spacing assumes slots every 25 mm. Measure the rail, and hold the cut rail against the marks before drilling.== - ==**The rear rail between the uprights.** It has about half a millimetre at each end. Check that it drops in with both end stops on.== - ==**Room under the VFD.** There is 17 mm between the VFD and the filter. If the H100's power and motor terminals face down, check the cables can bend in that space.== - ==**XT3 over the VFD.** About 25 control wires land 28 mm above the VFD's top, in its exhaust. Route them up and forward, not down across the vents.== - ==**KM1's temperature rating.** The DC-coil HMC-18B30 is rated to 40 °C ambient. It sits in the air stream to the fan, with its front corner 13.6 mm above the VFD's top.== - ==**Depth on the rail.** The NDR-480 is taken as 141 mm from the plate, about 2 mm uncertain. The relays are taken as 71 mm from the rail face and centred on the rail.== - ==**The FlexiHAL stack.** 55 mm deep is an estimate, and which board edges need wire room is not confirmed. It has 6 mm to the MDR-60, and its front end is 3 mm behind the AIR button's terminals, so check what plugs into that end.== - ==**The 16 mm buttons.** Their depth is read from Adafruit's drawing, not measured. Measure one, and check that its nut still has thread to grip on the 3 mm panel.== - ==**The control box.** Its size and position are placeholders from the mock-up. Check the 19 mm beside the enclosure handle by hand, and that the box does not get in the way of the E-stop.== - ==**Mean Well's clearances.** 40 above, 20 below and 5 either side come from the NDR installation manual; the same figures are applied to the SDR and MDR without checking theirs.== Still open between this layout and the wiring note, which otherwise agree on the rear rail, the end stops, the VFD on the lower rail, the controls, the valve outside the cabinet and what the drag chain carries: - ==**The end cover width,** as above.== - ==**The control box and top plate.** Their sizes are still the mock-up's placeholders until the printed part is drawn.== - ==**Which axis the drag chain serves,** and how the other motor, encoder and spindle cables are carried.== - ==**Rail stock for the lower rail,** as in the drill and tap list.== - ==**The VFD mount,** which is being designed. Its thickness here is a placeholder.== - ==**The rear-rail jumper bar.** The six green PE blocks, 5 to 10, need one jumper bar that spans all six. Check the stock, or cut one from a longer bar.== # References ## Related notes - [[Voron Cascade Electronics Wiring]]: Rev O. What connects to what; its terminal tables and wire labels use this layout's block numbers - [[Voron Cascade Electrical Configuration]]: jumpers, DIP switches, trims, HAL and INI, VFD parameters - [[Voron Cascade Bench Checks]]: what the bench still has to answer, including the parts this layout has not measured - [[Voron Cascade BOM]]: the Cascade BOM with order status - [[Electronics]]: parts in hand and the bench-jog wiring ## Sources - [Cascade Layout I](https://claude.ai/artifact/SMifPvbaUPLKZVGp382NJC), the published page this note was made from (2026-11-13, last revised 2026-11-15). It stays as the record of layout I and is not updated for J - [Cascade Layout H](https://claude.ai/artifact/6x97JWPPpbwiCHod5nkBEr) (revised 2026-11-11), the record of the layout before that - The Cascade CAD, for the panel holes, the fan, the inlet, the cable mounts and the frame - [Adafruit 16 mm illuminated pushbutton](https://www.adafruit.com/product/1477) and its [dimension drawing](https://cdn-shop.adafruit.com/datasheets/R16diagram.jpg) # Changelog ## 2026-11-15 - Created at Layout J, from the published Layout I page: the text is carried over and the figures are rendered again. One change from layout I, Erik's decision: the rear-rail PE group has one grounding block, at block 11, with blocks 5 to 10 green and jumpered and a 12 AWG wire link from block 10 to block 11. The rear-rail table, the bonding points, the back-panel view and the PE row of the change table follow. The lower-rail feed lands on block 6 and the gantry jumper on block 7. - Linked from [[Voron Cascade Electronics Wiring]], [[Voron Cascade Electrical Configuration]] and [[Voron Cascade Bench Checks]], which now name Layout J as the placement. ## 2026-11-16 - Took over the lower-rail jig and VFD-mount details that [[Voron Cascade Electronics Wiring]] used to repeat: the jig's outline, hole names and fourth bore, where the hole positions come from, the VFD hole positions, the face-to-plate depth and the old VFD jig files. The two figure captions no longer point at wiring-note sections, which are now a short summary that links here. No position changes; still Layout J.